PPGI Coil Buyer Guide – RAL 9002

ইমেল
হোয়াটসঅ্যাপ
ফেসবুক
টুইটার
লিঙ্কডইন

A 0.47 mm × 1220 mm PPGI or PPGL coil with a RAL 9002 finish is a quotation starting point, not a complete production specification. Buyers must confirm the substrate, steel grade, temper, coating mass, paint system, colour approval, tolerance, coil dimensions, forming route, packing and quantity. Z40, Z100 and AZ150 are separate coating options linked to the selected galvanized or galvalume substrate. The safest purchase record separates requested items from confirmed items. The final order should identify one substrate and one applicable coating designation.

Before approval, compare the dimensions with the forming route and project exposure. Confirm the colour by sample, record the visible face, and keep the technical schedule with the quotation. This prevents a provisional listing description from becoming an incomplete production instruction. Record the selected coating option beside the substrate so purchasing and production read the same specification. Keep the approved colour sample with the order record.

What should a buyer confirm before ordering a 0.47 mm × 1220 mm PPGI coil?

The requested thickness and width are useful because they define the initial mill enquiry, but they do not answer every question a coil supplier needs to price and produce the material. Ask whether 0.47 mm is nominal thickness or a guaranteed measured range, and whether 1220 mm is the delivered width or a slit width. The drawing or profile also matters. A roofing sheet line, a wall-panel line and a light fabricated component may impose different requirements on flatness, elongation, bend radius and surface protection.

Put the dimensions beside the application. If the coil will be roll formed, specify the profile, feed direction, visible face and minimum inside bend radius. If it will be cut into panels, confirm cut-length tolerance, burr expectations and whether a protective film is needed. Coil ID, outside diameter, maximum coil weight and loading direction should be agreed with the buyer’s decoiler and handling equipment. These details prevent an apparently correct width from creating problems at the processing line.

How do PPGI and PPGL differ in this quotation?

PPGI uses a galvanized steel substrate, while PPGL uses a galvalume or aluminium-zinc-coated steel substrate. Both can carry a painted surface, but the substrate coating is part of the product identity and should not be left implicit. The buyer should specify which substrate is required, what standard or grade applies, and whether the project needs a particular coating mass. A request that lists PPGI, PPGL, Z40, Z100 and AZ150 together still needs a final selection before production.

The choice should follow the service environment and forming route. Galvanized PPGI may suit a project that specifies a zinc coating on the steel substrate. PPGL may be selected where an aluminium-zinc substrate is required. Neither name alone proves outdoor durability, paint life or corrosion performance. Those outcomes depend on substrate, paint chemistry, coating thickness, edge treatment, fabrication damage and exposure. Buyers should ask for the technical data relevant to the selected system rather than combining the strongest-sounding values from different options.

For comparison, a galvanized product such as High UV Resistant PPGI Coil may be reviewed for a different outdoor coating requirement, while a PPGL product such as Light Steel Villa PPGL Coil represents a different substrate and application discussion. The comparison is useful only when the buyer checks the actual coating schedule and forming conditions.

How should RAL 9002 be approved for a colour-coated steel coil?

RAL 9002 should be recorded as a colour reference, not as a substitute for a physical approval sample. A screen image cannot reliably show the final appearance because lighting, gloss, viewing angle and monitor calibration alter the result. The order should identify the visible face, paint gloss, colour reference, sample approval method and acceptable colour tolerance. If the coil will be installed beside an existing panel, send a reference sample or define the matching requirement before production.

Colour approval also needs to be tied to the paint system. A light neutral colour can appear different on a smooth surface, a textured finish or a profile with changing reflections. The buyer should confirm whether the surface is intended for roofing, wall cladding, ceilings, partitions or fabricated panels. The back coat may have a separate colour and performance requirement. Protective film, if used, should be specified with removal timing so adhesive residue does not become a site problem.

A clear colour record might state: requested colour RAL 9002; visible face to be approved by sample; gloss and paint family confirm per order; back coat confirm per order. This wording keeps the commercial request useful without pretending that an unapproved sample is already a production guarantee.

PPGI PPGL galvanized and galvalume coating structure with RAL 9002 painted surface

How should Z40, Z100 and AZ150 be written in the order?

Z40 and Z100 refer to zinc coating options associated with galvanized steel, while AZ150 refers to an aluminium-zinc coating option associated with galvalume steel. The values should not be presented as interchangeable labels or combined into one specification. First choose the substrate. Then state the coating designation, the applicable standard, the measurement basis, the tolerance and any test or document requirement that has been agreed for the order.

The right coating depends on the project rather than the largest number on the page. Indoor panels, sheltered components, exterior roofing and coastal exposure may require different coating and paint decisions. Forming can also affect the practical choice because tight bends, slitting and roll forming place demands on the substrate and coating. Ask the supplier to confirm the selected coating against the application, not simply to quote every option at once.

Keep the purchase enquiry easy to audit. A useful table separates “requested” from “to confirm”: 0.47 mm and 1220 mm requested; galvanized or galvalume substrate to confirm; Z40, Z100 or AZ150 to select; RAL 9002 to approve; paint system and gloss to confirm. That structure reduces the risk that a provisional option is copied into a purchase order as if it were final.

What should the buyer include in a PPGI or PPGL coil enquiry?

Start with the product route: PPGI or PPGL, galvanized or galvalume substrate, intended application and processing method. Add the requested thickness, width, colour and coating option. Then ask for the information needed to close the specification: steel grade, temper, standards, coating mass, paint family, top-coat and back-coat thickness, gloss, colour tolerance, coil ID, outside diameter, coil weight, packing and destination.

For a roll-forming project, send the profile drawing or at least the bend sequence and minimum radius. For a cut-to-length project, state finished panel length and flatness expectations. For visible architectural surfaces, clarify the side that will face the building and whether protective film is needed. For repeat orders, identify the approved sample and the reference coil so the supplier can discuss colour and surface consistency against a real benchmark.

Commercial terms should remain separate from technical confirmation. Quantity, trial order size, delivery target and payment terms belong in the quotation discussion. Do not treat a supplier’s public listing price, MOQ, production capacity, certification statement or delivery estimate as a Bomis commitment. Request the commercial offer after the material schedule is clear, and keep every confirmed item in the quotation and order documents.

RAL 9002 PPGI PPGL coil building material applications

What processing and packaging points affect delivery?

Processing begins with how the coil will be handled after arrival. Slitting requires a finished width, slit-edge expectation and recoiling arrangement. Cut-to-length lines need a cut-length tolerance and flatness discussion. Roll forming needs a stable feed direction, tooling review and bend-radius check. Each route can change the acceptable combination of grade, temper, coating and paint system. Confirm these points before loading the material into production planning.

Packaging should match the coil weight, dimensions, lifting method and transport route. Confirm eye-to-side or eye-to-sky orientation, moisture protection, edge protection, marking, packing material and loading instructions. If the destination has humid or coastal conditions, ask for the agreed storage and transit protection rather than assuming standard packing is sufficient. The buyer should also define what documents accompany the shipment and which test or inspection records are available for the selected order.

These checks do not make the quotation slower. They make the quotation comparable. A supplier that receives the same dimensions, substrate, coating, colour and handling requirements can explain differences in price and lead time without mixing several product variants into one line.

FAQ: ordering a 0.47 mm × 1220 mm PPGI or PPGL coil

Is 0.47 mm × 1220 mm a confirmed Bomis specification?

No. It is the requested starting format. Confirm nominal thickness, tolerance, delivered width and processing route per order.

Can the order use RAL 9002?

Yes, as a requested colour reference. Approve a physical sample, gloss and visible-face requirement before production.

Should I choose PPGI or PPGL?

Choose the substrate that matches the project: galvanized PPGI or galvalume PPGL. Review coating mass, forming and exposure first.

Are Z40, Z100 and AZ150 the same coating?

No. Z40 and Z100 are galvanized options; AZ150 is an aluminium-zinc option. Select one designation with its substrate.

Which paint system is best?

There is no single answer without the environment and forming route. Confirm PE, SMP, HDP or PVDF after requirements are defined.

Can the coil be used for roofing?

Evaluate roofing use after the substrate, coating, paint system, profile, exposure and forming requirements are confirmed.

What should I send for a quotation?

Send substrate, grade, thickness, width, coating, colour, paint system, coil dimensions, quantity, packing, destination and processing.

How do I prevent colour disputes?

Use an approved physical sample. Record RAL 9002, gloss and visible face with the quotation and order.

Conclusion

A special-offer PPGI or PPGL request becomes order-ready when the buyer separates the requested dimensions from the confirmed material schedule. For this brief, start with 0.47 mm × 1220 mm and RAL 9002, then select the correct galvanized or galvalume substrate, choose Z40, Z100 or AZ150 as applicable, confirm the paint system, approve the colour sample and define processing and packing. Send the complete schedule to Bomis for a project-specific quotation.

কোম্পানির তথ্য

আরও তথ্যের জন্য আমাদের সাথে যোগাযোগ করতে দ্বিধা করবেন না।

অফিসের ঠিকানা

কক্ষ ১৩০৩, ভবন ২ জিনলিয়ান তিয়ানদি, ১৭৬ নং জুফেং রোড লিচাং জেলা, চিংদাও শহর, শানদং প্রদেশ

কারখানার ঠিকানা

জিংফু ইন্ডাস্ট্রিয়াল পার্ক, বক্সিং কাউন্টি, শানডং প্রদেশ, চীন

ইমেল সাপোর্ট

project@bomisgroup.com

চলুন কথা বলি

হোয়াটসঅ্যাপ: +৮৬ ১৮৩০০২৮২৫৭৩
ফোন: +৮৬ ১৮৩ ০০২৮ ২৫৭৩

যোগাযোগ করুন

আপনার কাছ থেকে শুনে আমরা আনন্দিত!

একটি মূল্য উদ্ধৃতি নিন

কোম্পানির তথ্য

আরও তথ্যের জন্য আমাদের সাথে যোগাযোগ করতে দ্বিধা করবেন না।

প্রধান কার্যালয়

Rm 1303, Bldg 2, Xinlian Tiandi, 176 Jufeng Rd Licang Dist, Qingdao, Shandong

ইমেল সাপোর্ট

project@bomisgroup.com

চলুন কথা বলি

হোয়াটসঅ্যাপ: +৮৬ ১৮৩ ০০২৮ ২৫৭৩
ফোন: +৮৬ ১৮৩ ০০২৮ ২৫৭৩